Marked to IS 303
Tulsi Gold Alternate Red White Gurjan Plywood
IS 303 marked plywood with a Gurjan face veneer over an alternate red-white core, treated against termite and borer attack.
Plywood & panel products · 20+ years
The grade stamped on the sheet is the grade you were quoted
Anyone can print “710” on a board. We publish the BIS licence number for every panel we supply, so you can check what you were sold against what you were promised — before it goes into your kitchen.
Or call +91 88788 67000 · Mon–Sat, 10am–7pm
Marked to IS 303, IS 710 and IS 1659
Standard, grade and BIS licence number stamped on the sheet — and published on every product page.
Specified honestly, not upsold
We recommend the grade the location needs. If a cheaper panel does the job properly, we will say so.
Quoted within one working day
Send a cutting list, a drawing or a photo and get a current rate with availability.
Our products
Boards people ask for by name
Each one is marked with its standard and licence number. Ask for a rate on any of them without leaving this page.
Marked to IS 710
Tulsi Premium BWP Grade Plywood
IS 710 boiling water proof plywood on a calibrated high-density hardwood core with a Gurjan face, carrying a 25 year guarantee.
Marked to IS 710
Club 710 Marine Hardwood Plywood
IS 710 marine grade hardwood plywood with a 100% Gurjan face, rated for high load bearing and 100% calibrated.
.jpg&w=3840&q=75)
Sapphire HDHMR Board (High Density High Moisture Resistant Board)
High Density High Moisture Resistant board — a homogeneous panel with no grain and no core voids, for painted, routed and membrane-pressed joinery.
.png&w=3840&q=75)
Marked to IS 1659:2004
GPI ISI Certified Block Board (Boric Acid Treated)
IS 1659:2004 block board in 19 and 25 mm, boric acid treated, available in MR and BWP core grades with a 25 year guarantee.
Marked to IS 710
Club 710 Gurjan Waterproof Plywood
IS 710 waterproof plywood with a 100% Gurjan face, high load bearing capacity and a 30 year warranty.
Which panel do you need?
Start with the room, not the product
Grade is decided by where the panel goes and what hits it — not by price. Pick the room and the specification is already narrowed down for you.
Product showcase
See the face, the core and the edge
Face veneer, core construction and edge quality decide whether a panel stays flat for a decade — and they are the three things a photograph on a listing will never show you.
What our customers say
Specified, delivered, and still right two monsoons later
Feedback from homeowners, designers and contractors across Madhya Pradesh.
We did the whole kitchen in 710 grade on their advice and kept the bedrooms on BWR to save money. Two monsoons later there is no swelling at the base of the units. Delivery turned up on the day they said it would.
I specify for eight or ten flats a year, so what I need is consistent stock and a straight answer on grade. I have had both here. One batch of shutters came through with a face I was not happy with and it was replaced without an argument.
Rates are competitive, but that is not why I keep going back. The ISI mark and the licence number are printed on every sheet, so I can show a client exactly what went into their job.
We did the whole kitchen in 710 grade on their advice and kept the bedrooms on BWR to save money. Two monsoons later there is no swelling at the base of the units. Delivery turned up on the day they said it would.
I specify for eight or ten flats a year, so what I need is consistent stock and a straight answer on grade. I have had both here. One batch of shutters came through with a face I was not happy with and it was replaced without an argument.
Rates are competitive, but that is not why I keep going back. The ISI mark and the licence number are printed on every sheet, so I can show a client exactly what went into their job.
Buying with confidence
Check the sheet, not the salesman
Anyone can print “710” on a board, and in this trade plenty of people do. The mark that actually means something is the ISI mark carrying an IS number and a BIS licence number — because that licence is registered, and registered things can be checked.
So we publish ours. Every product page shows the standard and the licence number stamped on that board, before you buy rather than after.
Look for the IS number first
IS 303 for interior plywood, IS 710 for marine and BWP, IS 1659 for block board. A sheet with no IS number is not a grade — it is a description.
Then check the BIS licence
The CM/L licence number ties that mark to a registered manufacturer. We publish it for every product, so you can check it before the sheets arrive.
Match the delivery to the quote
Grade, type, thickness, size and batch are stamped on each sheet. That is what lets you confirm you were sent what you paid for.
See it before you commit
Screen images cannot show face quality or how an edge machines. Ask for a sample — we would rather you checked than took our word for it.
Tools
Work it out before you order
Two free tools for the awkward part of a project — sizing the order and settling on a palette.
Journal
Guides, trends and technical notes
Written for people specifying materials, not for search engines.
Enquire
Send us your cutting list, get a price back
Tell us the thickness, grade and quantity — or just describe the space and we will recommend the specification. No obligation, and no pressure to take the dearer panel.
I am a…
What happens next
You send the details
A cutting list, a drawing, or a description of the space. A photo on WhatsApp is enough to start.
We come back with a specification
The grade the location needs, the sizes that waste least, and a current rate — within one working day.
Samples, then delivery
See the face quality before you commit. Delivery and freight are confirmed with you before anything ships.
20+
Years in the trade
14
Products in the catalogue
30 yr
Longest warranty supplied